1. Smart Forum

  2. Facebook

  3. Auto-Software

  4. Auto-file.ORG

  5. EPC SOFTWARE

  6. Support US

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Caterpillar SIS 2019-01 + installation guide
#1
CAT 
Caterpillar SIS Full DataSet 2019-01 + Step-by-step installation guide

Size of installation is 133GB

[Image: 7e40425074b87ca24ad85cecbb182557.jpeg]

Free Mega.nz link, no passwords.  

"Thanks" and "Reputation" are welcome)


Attached Files
.rar   Caterpillar.rar (Size: 402 bytes / Downloads: 93)
.txt   Virtuals LIST.txt (Size: 50 bytes / Downloads: 47)
  Reply
Thanks given by: gabbiiiyyyy , Admin , doctech101

#2
Hy

Please help me.... no pictures

error message
" Graphics error. Please contact PC administrator to install and setup the SIS Graphics Plug Ins available on the SIS downloads page "

I was trying to download the recommended CreoView version within the program / under downloads. but not available.
i tried the new 5.1 too but no improvement.
Installation everything I did well would work just no picture.

Please help
  Reply
Thanks given by:

#3
Hello!

In the "Additional" folder, there are Sis_DejaVu and IsoView files, try installing these libraries (run as administrator), then restart the computer. It might be help.

And in general - run any installation of such programs on behalf of the administrator, since without proper rights, some libraries or program parts may not be properly written to the system.

If nothing helps, reinstall it again, or try installing it on another computer, maybe it's time to clean Windows or reinstall it.

I hope you succeed! Have a nice day!
  Reply
Thanks given by:

#4
(01-30-2020, 12:08 PM)bookini Wrote: Hello!

In the "Additional" folder, there are Sis_DejaVu  and IsoView files, try installing these libraries (run as administrator), then restart the computer. It might be help.

And in general - run any installation of such programs on behalf of the administrator, since without proper rights, some libraries or program parts may not be properly written to the system.

If nothing helps, reinstall it again, or try installing it on another computer, maybe it's time to clean Windows or reinstall it.

I hope you succeed! Have a nice day!

Hy

Thank you, but it failed.
I can't install from this folder.
error message is:
"file is corrupt"
protection is all off,
a brand new system with just 2 snowy clean windows
I installed 2x-3x again and failed and tried to install it with the new 2019.07 installer but it's not good either.
I tried to enable all flash in Exploirer, Chrom ... but nothing.

I don't know if anyone has come this way but if you can please help
Thanks

HELP the fourm as we did , Donate NOW !
[Image: btn_donateCC_LG.gif]
  Reply
Thanks given by:

#5
(01-30-2020, 07:34 PM)Kareee Wrote:
(01-30-2020, 12:08 PM)bookini Wrote: Hello!

In the "Additional" folder, there are Sis_DejaVu  and IsoView files, try installing these libraries (run as administrator), then restart the computer. It might be help.

And in general - run any installation of such programs on behalf of the administrator, since without proper rights, some libraries or program parts may not be properly written to the system.

If nothing helps, reinstall it again, or try installing it on another computer, maybe it's time to clean Windows or reinstall it.

I hope you succeed! Have a nice day!

Hy

Thank you, but it failed.
I can't install from this folder.
error message is:
"file is corrupt"
protection is all off,
a brand new system with just 2 snowy clean windows
I installed 2x-3x again and failed and tried to install it with the new 2019.07 installer but it's not good either.
I tried to enable all flash in Exploirer, Chrom ... but nothing.

I don't know if anyone has come this way but if you can please help
Thanks

Caterpillar is normally works only in Internet Explorer. Do not need to use installer from 2019/07, dont have a patch.
Install Java too, it is important.

Here are a couple of tips from the Russian forum on your topic:

1. Problem - IsoView cannot be used in Protected Mode
The solution is to go to the Internet exploler, in the top menu Tools, select Internet options, the Security tab, select reliable sites, the slider to the bottom and everything will work.
2. The problem is Graphics error. Please contact PC administrator to install and setup the SIS Graphics Plug Ins available on the SIS downloads page
The solution is to install djvuctrl-6.1.4-en-r34387.msi. Try installing the PTC Arbortext IsoView and PTC Creo View Consumer again. How many times reinstalled them, I find it difficult to say. All programs can be downloaded by opening SIS and the Downloads tab. But in the end, all the pictures are loaded fully!
  Reply
Thanks given by: Kareee

#6
(01-30-2020, 08:09 PM)bookini Wrote:
(01-30-2020, 07:34 PM)Kareee Wrote:
(01-30-2020, 12:08 PM)bookini Wrote: Hello!

In the "Additional" folder, there are Sis_DejaVu  and IsoView files, try installing these libraries (run as administrator), then restart the computer. It might be help.

And in general - run any installation of such programs on behalf of the administrator, since without proper rights, some libraries or program parts may not be properly written to the system.

If nothing helps, reinstall it again, or try installing it on another computer, maybe it's time to clean Windows or reinstall it.

I hope you succeed! Have a nice day!

Hy

Thank you, but it failed.
I can't install from this folder.
error message is:
"file is corrupt"
protection is all off,
a brand new system with just 2 snowy clean windows
I installed 2x-3x again and failed and tried to install it with the new 2019.07 installer but it's not good either.
I tried to enable all flash in Exploirer, Chrom ... but nothing.

I don't know if anyone has come this way but if you can please help
Thanks

Caterpillar is normally works only in Internet Explorer.  Do not need to use installer from 2019/07, dont have a patch.
Install Java too, it is important.

Here are a couple of tips from the Russian forum on your topic:

1. Problem - IsoView cannot be used in Protected Mode
The solution is to go to the Internet exploler, in the top menu Tools, select Internet options, the Security tab, select reliable sites, the slider to the bottom and everything will work.
2. The problem is Graphics error. Please contact PC administrator to install and setup the SIS Graphics Plug Ins available on the SIS downloads page
The solution is to install djvuctrl-6.1.4-en-r34387.msi. Try installing the PTC Arbortext IsoView and PTC Creo View Consumer again. How many times reinstalled them, I find it difficult to say. All programs can be downloaded by opening SIS and the Downloads tab. But in the end, all the pictures are loaded fully!

finally succeeded
protected mode was the solution
thank you thank you thank you thank you ....
You are God :9

HELP the fourm as we did , Donate NOW !
[Image: btn_donateCC_LG.gif]
  Reply
Thanks given by: bookini

#7
You can just press Thanks and Reputation ))


Attached Files
.txt   Virtuals LIST.txt (Size: 50 bytes / Downloads: 12)
  Reply
Thanks given by: Kareee , Admin , Palbert




Possibly Related Threads…
Thread Author Replies Views Last Post
CAT Caterpillar SIS Full 2020-01 installation bookini 8 11,491 11-06-2020, 05:10 PM
Last Post: bookini

Forum Jump:


Users browsing this thread:
1 Guest(s)

AUTO EPC

Welcome to Auto-EPC.org


  Register

AUTO-EPC.ORG