auto-epc.org
BOSCH ESItronic Tutorial install - Printable Version

+- auto-epc.org (https://www.auto-epc.org)
+-- Forum: The Normal Main Forum (https://www.auto-epc.org/forumdisplay.php?fid=5)
+--- Forum: Installation Guides, Procedures & Tutorials (https://www.auto-epc.org/forumdisplay.php?fid=12)
+--- Thread: BOSCH ESItronic Tutorial install (/showthread.php?tid=784)

BOSCH ESItronic Tutorial install - Admin - 10-22-2011

BOSCH ESItronic Tutorial install

1. Mount your ESI tronic image

2. Run Setup and you will see this:

[Image: image001t.png]

Sometimes it takes few seconds sometimes minutes till it become 100%, it depends on the computer or OS.

3. After it will become 100% you will see this

So choose your language and continue

4. Then you will see this:

[Image: image005n.png]

I always use the user defined installation, I never put any I-key (As I remember if you put FFFF – you will install all the bases – I don’t need them all – so it depends on you). Even if you don’t put any I-key you will

be also able to install full package – see next steps)

5. Then you will see this:

[Image: image007.png]

Change the installation directory if you wish then continue

6. Then this:

[Image: 21736731.jpg]

I always “tick” the: KTS 505-670 program CAS (you need to install the main program) and Data download

(It will make possible to install needed bases ) If you need other options like screen saver or Fuel injection

pump section – tick them.

7. Then this:

[Image: 56221828.jpg]

Now install the bases that you need using “drag and drop” method – to the drive that you wish. I use this

bases:

[Image: 66269594.jpg]

It depends on what you need or how much disk space you have. If you wonna learn more about the bases

read the attached: brochure_esi-tronic.pdf

8. Then this:

[Image: 46916312.jpg]

RE: BOSCH ESItronic Tutorial install - Admin - 10-22-2011

Just continue.

9. Then this:

[Image: 39356435.jpg]

And wait till the installation ends. Remember that it will ask you about DVD 2 and/or DVD3 – it depends

on which bases you wonna install. As I remember the A and C bases are on DVD1 but if during the

installation you will not have DVD2 or DVD3 the installator will omit the bases but the install will finish

with success - you will just not be able to use the omitted informations.

10. Then this:

[Image: 26742846.jpg]

Just close.

11. Then this

[Image: 46170736.jpg]

I always klick NO. I don’t know why ? Maybe because I am to lazy to get my KTS and connect it to my

USB port - usually it is about 2 meters away from me Anyway I will show later how to configure the

KTS – So click NO. First we finish ESI install and activation.

12. Then this:

[Image: 60263852.jpg]

Just restart your PC.

13. Then this:

[Image: 64676351.jpg]

Click Execute, and this appears:

[Image: 83986623.jpg]

Just put any customer no (8 or 10 digits). Put 0123456789 (or your original Customer no.) and call Bosch

to get your Release code or copy ID no. to keygen, generate it and paste to Release code window.

After that you should see this:

[Image: 94844307.jpg]

Then close the Display release information window and close the ESItronic application

Done



RE: BOSCH ESItronic Tutorial install - krazycart - 10-23-2011

thanks for this one question where do you get the key generator as I don't really want to have to ring Bosch.



RE: BOSCH ESItronic Tutorial install - Admin - 10-23-2011

(10-23-2011, 06:15 AM)krazycart Wrote: thanks for this one question where do you get the key generator as I don't really want to have to ring Bosch.

Post your ID Number in the Activation and passwords section , and sure you will get your Activation code .Blush

RE: BOSCH ESItronic Tutorial install - husertas - 02-23-2012

Hello Friend,
I have a Bosh KTS 540 diagnosis device.
I have installed all the ESI tronic software. No problem, thanks.

But ESI don't find KTS 540. I did everything but but it says "no sd".

What is that? Can you advice me please?



RE: BOSCH ESItronic Tutorial install - gaby - 02-24-2012

(02-23-2012, 07:54 PM)husertas Wrote: Hello Friend,
I have a Bosh KTS 540 diagnosis device.
I have installed all the ESI tronic software. No problem, thanks.

But ESI don't find KTS 540. I did everything but but it says "no sd".

What is that? Can you advice me please?

CONFIGURATION / FIRMWARE UPDATE

RE: BOSCH ESItronic Tutorial install - fredon1977 - 03-12-2012

good evening
I have a KTS 540 with an electronic program Esi 2007/2, now that I had a program 2011/2 and I do not know how the update, I even deleted the electronic version of Esi 2007 / 2 on my computer but when I click on the icon of the configuration via my external hard drive gives me this message (the data carrier in the reading is not legible) help me plzzzzzzz


RE: BOSCH ESItronic Tutorial install - HappyNic07 - 08-25-2016

Good day team

I have installed ESI Tronic 2015/1 on my pc and typed in the release code
how do I get past the Insert ESI tronic disk when you click on any of the options can anybody provide me with a way or a disk image or patch.
kind regards
Nicolas.

RE: BOSCH ESItronic Tutorial install - sarcasmo - 06-25-2017

I paid 120 euro not for unseen images...........and moderator dont take the work to upload it again, this is a fraud

RE: BOSCH ESItronic Tutorial install - tiger1984 - 06-25-2017

(06-25-2017, 12:34 PM)sarcasmo Wrote: I paid 120 euro not for unseen images...........and moderator dont take the work to upload it again, this is a fraud

Hello

First, it would be nice to introduce yourself in this thread:
http://auto-epc.org/forumdisplay.php?fid=4

Please pay more attention to the date of creation this thread, it was created about six years ago (22.10.2011, 10:27 AM).
This thread is placed in "Normal Main Forum" and it's free so this is not a fraud.
Please next time contact creator of thread to reupload expired links. There is no need for such statements, we are people and we can arrange in a nice way.

Thank you for your donation. With your donation you get Premium Member status and you have access to the contents from "Smart Forum" (Links & Passwords).


Regards